AntennaPointer

Feed-horn polarization for geostationary satellites.

1

Pointed satellite

Satellite (type a name or position, or open the list)
Orbital position (longitude)
2

Earth station & antenna

Fixed view of this Earth station; the dashed line points to the satellite.

Pol drive angles — downlink

Enter site and satellite coordinates.

Decimals
Horizontal— 
Vertical— 
Antenna azimuth—  
Antenna elevation— 
Polarization skew
—
 
Longitude difference
—
 
Range & cross-check▾
Slant range
—
 
Classic formula skew
—
atan(sinΔL / tanφ)
Drive readout — 90° to 270° travel
Feed E-field, viewed from behind the dish
—
Pol drive angle: set the drive here, both LNBs line up

Beacons & telemetry

Frequencies in MHz · H V linear, L R circular · IF for a standard LNB

Peak the dish on a beacon, then turn the feed for the deepest null on the opposite polarization. Source: .

Transponders

Your own list for this satellite · frequencies in MHz

1

Earth station

Latitude
Longitude

Location on the map

Click to move this Earth station, drag to pan, scroll to zoom. The dashed line points to the satellite.

2

Antenna

Bands (pick all the antenna works on)
Offsets & travel limits▾
Offsets (degrees, added to the true angle to give this antenna's readout)
Use a minus sign to subtract, e.g. −22.3 elevation for an offset-fed dish read on its back plate. Don't know them? Peak on a satellite and press Find offsets from a peak at the top of this card.
Travel limits (degrees on this antenna's readout, leave empty for no limit)
Azimuthto Elevationto
Satellites outside these limits are marked as out of reach. An azimuth range can pass through north, e.g. 300 to 60.
Feed & pol drive▾
Feed
180° on the drive equals
Polarization at 180° when the satellite is due south (zero skew).
Reading increases when feed turns
Viewed from behind the dish, looking toward the satellite.
LO bands▾
LO bands (MHz: each band's LO and the frequencies it covers)
Add as many bands as the antenna's LNB or downconverter has. Beacon IFs use them; with no bands, a standard LNB is assumed.

Saved antennas

Az offsetEl offsetPol offsetPointed satellite

Click a row to open that antenna and its Earth station in the cards above, to check or change them. Use opens it on the Calculator; × deletes it.

Backup, sharing & password

Earth stations, antennas, your satellite names, status marks and added satellites are kept in this browser. Copy them to a file, share them with other computers, or lock them with a password.

Backup file

All of it as one small .json file: keep a copy, or move it to another computer or to the other edition of this page.

Shared data file

Edit password

All satellites from this site

Pick an Earth station on the Calculator.

Beacons (MHz)
 
 

Click a row to load it into the calculator, or a column heading to sort by it. Use + name and status on a row to add your own names and status mark. custom added by you · partly operational standby CelesTrak's status · dashed border: your own mark. Positions from ; more under How it works.

Coverage

Beam footprints See where this satellite's beams reach (C, Ku and Ka bands) on SatBeams.
Open beam footprints ↗
Satellite above the horizon Dish elevation rings (0°, 10°, 20°, 30°, 45°, 60°) Satellite Your site

Drag to pan, scroll or use +/− to zoom, click anywhere to check that spot. The shaded area shows where the satellite can be seen — it is not the beam footprint. Load the operator's footprint file for signal levels.

Clicked point

Footprint files

    Load beam footprint files (KML/KMZ) from the satellite operator, or ones you have downloaded for your own use, to see beam contours here offline. Line and polygon footprints are remembered in this browser; image footprints stay until the page is closed.

    How the angle is found

    A geostationary satellite transmits its vertical polarization parallel to the Earth's rotation axis and its horizontal polarization parallel to the equatorial plane. Unless the satellite sits exactly on your meridian (due south), the satellite's “vertical” does not line up with your local vertical. The difference is the polarization skew, and the feed horn has to be rotated by that amount.

    1. Skew

    The calculator places your site on the WGS-84 ellipsoid and the satellite on the geostationary orbit (radius 42 164 km), then projects the Earth axis and your local “up” onto the plane square to the line of sight. The angle between them is the skew — exact, with no small-angle approximation. The well-known textbook formula gives almost the same result and is shown for comparison:

    skew = atan( sin(site_lon − sat_lon) / tan(site_lat) )

    Sign: positive = clockwise when you stand behind the dish looking toward the satellite. In the northern hemisphere a satellite west of you gives clockwise skew; a satellite east of you gives counter-clockwise skew.

    2. The 360° method, 90°–270° travel

    The drive scale reads 0–360°, but the feed only moves between 90° and 270°: a 180° window centred on 180°. Because a linear polarization repeats every 180°, every polarization has exactly one position inside that window, and H and V are always 90° apart.

    V reading = 180 + skew (default: 180° = V, clockwise increases)
    H reading = V reading ± 90 (whichever stays inside 90–270)
    Satellite positionSkewV readingH reading
    Due south (same longitude)0°180°90° / 270° (end stop)
    West of youclockwise (+)above 180°V − 90°
    East of youcounter-clockwise (−)below 180°V + 90°

    If your controller is set up differently, change it on the Antenna card: pick whether 180° means vertical or horizontal, which way the reading increases, and add a pol offset if your encoder's zero is shifted. These drive settings are kept with each antenna.

    3. Peaking on the real signal

    • Drive to the calculated angle, then trim for maximum co-pol and the deepest cross-pol null on a spectrum analyser.
    • If the measured best position is consistently off by the same amount on every satellite, enter that difference as the antenna's pol offset.
    • Readings are for the downlink (receive) port. With an orthogonal Tx/Rx feed, the transmit port sits 90° away.

    Antenna profiles

    Each saved Earth station can hold any number of antennas. An antenna has a name, a dish size, three offsets and its own drive settings (what 180° means and which way the reading increases). Earth stations and antennas are added and changed on the Stations & antennas tab (New on either card clears it to add another; it asks first if something is not saved): save the Earth station first, fill in the Antenna card next to it and press Save antenna. Choosing the site later brings back the antenna you used there last; pick another from Antennas at this site. The Antenna card keeps the less-used settings in three sections, Offsets & travel limits, Feed & pol drive and LO bands: click one to open it; when closed, each shows its current values on one line. Decimals (next to Copy on the results) sets how many decimal places every reading shows.

    On the Calculator, the Earth station & antenna card under the satellite lists every saved Earth station with its antennas underneath. Click a station to use it (with the antenna you used there last), or an antenna to use it and its station; the ones in use are highlighted, and Edit opens the Stations & antennas tab. Click the highlighted antenna again to stop using it: no antenna's offsets, travel limits or LO bands apply (180° = V, clockwise, linear feed). That Earth station then opens with no antenna until you pick one, even if it has only one antenna.

    Which antenna can point at a satellite? Pick the satellite first. Each antenna in the Earth station & antenna card gets a green dot if that antenna can point at it, or a red dot if it can't (hover to see why: below the horizon or outside its travel limits). A line above your saved Earth stations counts them, for example 2 of 3 saved antennas can point at ARABSAT-5A; clicking it opens the Stations & antennas tab with Only antennas that can reach ticked.

    The Stations & antennas tab lists every saved antenna with its Earth station (name and position) and all its settings: offsets, travel limits, drive settings and LO bands. The last column shows the H and V drive readings and the azimuth and elevation that antenna would need for the satellite on the Calculator, or Out of reach with the reason. Search by antenna, Earth station, band or LO frequency, and sort it: click a column heading (Earth station, Antenna, Azimuth travel, Elevation travel, Drive or LO bands) to sort low to high or A to Z, and click it again for high to low. Sort by also offers size and band, and the button next to it flips the direction. Azimuth travel sorts by how wide the travel is, elevation travel by the lowest elevation the antenna reaches, and LO bands by the lowest LO; antennas missing that value go last either way. The order is remembered. Click a row, or Use, to work with that antenna on the Calculator; × deletes it (after asking).

    • Azimuth and elevation offsets are added to the true angles to give what this antenna's own scales or controller read, shown under the H and V readings as Antenna azimuth and Antenna elevation. Use a minus sign to subtract. For example, an offset-fed dish whose elevation is read on its back plate needs its offset angle subtracted (−22.3 for a 22.3° offset dish).
    • Pol offset is added to the H and V drive readings, on this page and in the satellite table.
    • Travel limits are how far this antenna can move, on the same readout as above (true angle plus offset). A satellite outside them is out of reach: the calculator shows a red warning, the satellite list puts it under Out of this antenna's travel, and the All satellites tab marks it and can hide it. Leave a box empty for no limit. An azimuth range can pass through north: 300 to 60 means from 300° round through 0° to 60°.
    • Size gives the dish's 3 dB beamwidth (about 70 λ / D), a guide to how finely it has to be peaked.
    • LO bands describe the antenna's LNB or downconverter, with as many bands as it has (two for a universal Ku LNB, three or four for some multi-band setups): a name such as Low, Mid or High, the LO frequency, and the lowest and highest frequency that band covers, all in MHz. Fill from a common LNB enters a universal Ku or C-band LNB for you. The beacon list then shows each beacon's IF from the band that covers it (IF = the difference between the beacon and the LO, so a C-band LO above the signal works too), with the band's name; a beacon no band covers is marked no LO band. With no bands, a standard LNB is assumed.
    • Bands are the frequency bands the antenna works on: L, S, C, X, Ku and Ka (pick more than one for a dual-band dish, e.g. C and Ku). They show next to the antenna on the Calculator and in the table, and the beacon list greys out beacons outside them (marked not C/Ku, with no IF). With no band picked, every beacon is shown as usual.
    • Feed is Linear, Circular or Switchable. A circular signal (left- or right-hand, L or R) has no polarization skew, so a circular feed has no angle to set: the Calculator shows a note instead of the H and V readings and dials, the satellite and antenna tables show no drive readings for it, and the beacon list marks the L and R beacons to peak on, with linear (H/V) beacons about 3 dB down. A switchable feed (polarizer switched in or out) keeps the H and V readings for its linear mode. Dual LNB (V + H) is a feed with two LNBs set 90° apart (an orthomode transducer): one drive reading sets both, so the Calculator shows the V reading as the feed position, marks H as automatic, and adds a Pol drive angle dial with one needle at that reading. A satellite with only an H beacon is fine: peak it on the H LNB and null it on the V LNB, and the drive reading is the same. Find offsets from a peak then takes the reading as the feed position, with no V or H to pick. If the receivers come out swapped, the feed is a quarter-turn off.
    • The Azimuth (true) and Elevation figures under the dials, and the satellite table, always show the true angles.

    Changing a saved antenna: click its row in the table on the Stations & antennas tab (or pick it from Antennas at this site), change anything on the Antenna card, including its name, and press Update antenna. The page lists every change before saving it, for example Elevation min: 5° → 7°. If you type a new name, Save as new adds it as another antenna and keeps the original; to rename the original instead, press Update “…” next to it. New (next to Delete) clears the card to add another antenna from scratch.

    The antenna card says whether what is on screen is saved: Changes not saved means the offsets or settings differ from the saved antenna. Saving the Earth station again with a new location keeps its antennas; deleting it deletes them too.

    Finding an antenna's offsets from a peak

    If you don't know an antenna's offsets, let the antenna show you. Open it on the Antenna card, press Find offsets from a peak at the top of the card, then:

    1. Peak the antenna on a satellite, on a steady signal such as a beacon. For pol, turn the feed for the deepest null on the opposite polarization: the null is much sharper than the peak.
    2. Pick that satellite and type what the controller reads for azimuth, elevation and pol, and whether the feed was set for V or H. Leave out any reading you don't have.
    3. Each offset is the reading minus the true angle the page computes. Use these offsets puts them on the Antenna card; for a saved antenna it then asks to update it, listing the changes.

    Pick a satellite well above the horizon, 15° or more: lower down, the atmosphere bends the signal and the elevation reads a little high. Don't use one marked drifting: it isn't held at its listed position. One you added yourself must not be in inclined orbit, or it isn't where the page computes. The pol offset uses the drive settings on the card (180° = V or H, and the direction), so set those first. For a surer result, add one or two more satellites spread across the arc: the offsets are averaged, and the page says if they disagree. A difference between east and west usually means the mount isn't level, so one offset can't fit the whole arc.

    Backup and moving to another computer

    Earth stations, antennas, your other names, status marks and added satellites are kept in this browser on this computer, not in the page file. Another browser, another computer or the other edition of this page (Antenna Pointer and Offline Satellite Pointer) each start empty, and clearing the browser's site data deletes them. To keep a copy or move them, press Export under Backup, sharing & password on the Stations & antennas tab: it saves one small .json file. Open the page where you want the data, press Import and pick that file. The page lists what it will add before importing. Nothing is deleted: Earth stations and antennas with the same name are replaced by the ones in the file, and everything else is added.

    Sharing between computers

    Several computers can keep the same Earth stations, antennas, other names, status marks and satellite list through one shared data file, for example in a shared network folder. This needs Chrome or Edge.

    1. On the first computer, press Create file under Shared data file on the Stations & antennas tab, go to the shared folder and save the file. Its data goes into the file.
    2. On each other computer, press Link file and pick the same file. Its Earth stations and antennas are added to that computer; where the same item is on both, the file's version is kept.
    3. From then on, every change on any linked computer is written to the file, and the others pick it up when the page is opened, when you come back to it, or within about 10 seconds while it is open.

    Changes are merged item by item, so two people working on different antennas or Earth stations at the same time keep both changes, and deletions reach every computer. If the same antenna is changed on two computers at once, the last change wins. What is on screen (the site, satellite and antenna you are working on, light or dark theme) stays separate on each computer.

    After the browser is restarted, Chrome or Edge may ask once more: a yellow bar under the tabs says the file isn't connected, and Connect allows it. If the shared folder can't be reached, changes are kept on the computer and sent once it can. Unlink stops sharing on that computer and leaves the file for the others. A shared data file can also be loaded with Import, like a backup.

    Edit password

    To stop Earth stations, antennas and the satellite list from being changed by mistake, press the padlock at the top of the page, or Set password under Edit password on the Stations & antennas tab. Without the password, anyone can still pick satellites, Earth stations and antennas, point with them, and export a backup. Saving, changing and deleting Earth stations and antennas, other names, status marks, adding or removing satellites, Import, and linking or unlinking the shared data file need it.

    When the password is set, the page shows a recovery code once. Write it down: if the password is forgotten, Forgot the password? in the unlock box takes the code and lets you set a new one. To edit, press the padlock at the top (or Unlock) and enter the password. It stays unlocked on that computer until you press the padlock again or Lock now, or reload the page. Computers linked to a shared data file share the password, so it is set once for all of them.

    The password is kept only as a scrambled (hashed) value, never as readable text. It guards against mistakes and casual changes, not against someone determined: anyone who can edit the page file or clear the browser's data can get past it. For real protection, use Windows folder permissions as well.

    Magnetic azimuth

    Every azimuth on this page is measured from true north. Under Antenna azimuth, the Magnetic line gives the same direction as a hand compass reads it: the true azimuth less the magnetic declination, the angle between true and magnetic north at the Earth station (east is positive, so 3° E means the compass reads 3° less than the true azimuth). It is worked out for today's date from the World Magnetic Model 2025, which is built into the page and runs to the end of 2029; after that the page says the model is out of date. The same bearing is in the copied result, the antenna table and the coverage map's click readout. The antenna's azimuth offset does not change it.

    Use it for rough pointing only. The model is good to about half a degree in most places, but the steel of a dish, a mount or a vehicle can pull a compass several degrees off: stand a few metres back, sight along the line, then peak on the signal.

    Entering coordinates

    Decimal degrees (24.7136), degrees–minutes–seconds (24 42 49 or 24°42'49"), or degrees and decimal minutes (24 42.82). A trailing letter (46.67E) or a minus sign (-7 = West / South) sets the hemisphere automatically.

    Location map

    On the Calculator, card 2 shows a fixed map of the Earth station in use, with a dashed line toward the satellite. It follows the station and antenna you pick and can't be moved by accident. To move a station, click that map (or Move it on the map): it opens the movable map under the Earth station card on Stations & antennas, where a click places the station, dragging pans and scrolling zooms. Expand opens that map over the whole screen, where it works the same way; Close or the Esc key brings it back. The map type (online street or satellite map, offline street map, simple offline map) is chosen there and used in both places.

    Coverage map

    On the Coverage map tab, Open beam footprints opens SatBeams' footprint map for the selected satellite (C, Ku and Ka beams) in your browser; that needs internet. The map below it works offline and shows where on Earth the selected satellite is above the horizon, with rings for dish elevation angles. Click any spot to see its elevation, azimuth, skew and the H/V drive readings from there; Use as Earth station copies that spot into the calculator. This is geometry only — actual signal coverage depends on the satellite's beams, so load the operator's KML/KMZ footprint file on top, or open the satellite on SatBeams (internet needed).

    Pinned and recent satellites

    Under the satellite box, the Calculator keeps the last five satellites you picked and any you pin with Pin this satellite; click one to load it. Press / anywhere on the page to jump to the satellite box. Pins and recent satellites are kept in this browser.

    Other satellite names

    Many satellites are known by more than one name: renamed after a sale or a move (Eutelsat 33F was Hot Bird 8), a second operator's name (Hellas Sat 4 is also SaudiGeoSat 1), or an amateur radio name (Es'hail 2 is QO-100). The All satellites tab shows these under the main name, from CelesTrak's satellite catalogue annex, SatNOGS DB and the names the beacon list uses. Names you add yourself with + name are shown first, kept in this browser, and stay attached to the satellite when the list is updated.

    Transponders and frequency plans

    The Transponders card under the beacons keeps your own list of transponders for each satellite: frequency (MHz), polarization, symbol rate (ks/s) and a note such as the channel or carrier. Press Edit list to add rows, or Paste a list with one transponder per line (11747 H 27500 MBC; 27.5 Msps, decimal commas and columns copied from a table work too), check the rows and press Save list. For each one the card shows the IF to set on the meter or receiver (with the antenna's LO bands, or a standard LNB) and the Drive reading for its polarization with the antenna on the card. The lists are kept by satellite, so they survive satellite list updates, and they go into the backup file and the shared data file with your Earth stations.

    Frequency plan shows the satellite's published frequency plan chart (transponders, beams, beacons, uplink and downlink) right in the card, under your list, for satellites. It stays open and follows the satellite you pick; zoom and scroll it with the viewer's own controls, press Full screen for a bigger view, New tab to open it on its own, and Close or Esc to hide it. The charts come from frequencyplansatellites.altervista.org, whose notice says anyone can use and link its data, and are kept on this site, so they open right here.

    Channels & frequencies (LyngSat)

    Under the satellite box, the on LyngSat link opens that satellite's LyngSat page (TV and radio channels, transponder frequencies, polarisation, symbol rates) in your browser; it needs internet. The app matches the satellite by its names and orbital position. Other satellites LyngSat lists at the same position are linked next to it. If LyngSat has no page under that name, the link opens its full list for that part of the sky. Nothing from LyngSat is stored in the app.

    Satellite status

    Satellites that CelesTrak’s satellite catalogue lists as partly operational, standby, spare and so on are marked on the All satellites tab. If you know better — a satellite was retired, is now a backup, or is back in service — use status on its row to set it yourself: operational, partly operational, standby, spare, extended mission, not operational (dead) or unknown. Your choice has a dashed border, is kept in this browser, and stays with the satellite when the list is updated; pick Automatic to go back to CelesTrak’s status. Satellites with no mark are fully operational, and dead ones are greyed out; hover a mark for what it means.

    The built-in list holds satellites close to the equator plane (inclined ones are left out). A satellite moving along the arc by 0.1° a day or more, because it is being moved to a new slot or retired, stays in the list marked drifting: hover it to see how fast and which way, and where it would be today. When it settles at a new slot, the next update shows it there without the mark. Satellites you add at the bottom of the All satellites tab are marked custom and are kept when the built-in list is updated. To add other names to a satellite, use + name (or edit) on its row and separate them with commas; search finds a satellite by any of its names.

    Beacons & telemetry

    The Beacons & telemetry card under the results lists the beacon frequencies of the pointed satellite, and of any other satellites sharing its orbital position, with polarization (H, V, L, R) and the beam where known. IF is the frequency to set on a satellite meter: Ku-band on a universal LNB (9.75 / 10.6 GHz), C-band on a 5.15 GHz LNB, or the selected antenna's own LO bands when it has them. A beacon is an unmodulated carrier that is always on, so it is ideal for peaking the dish and finding the cross-pol null. The list covers Asia, the Middle East, Europe, Africa and the Atlantic, about 61°W eastward to 167°W; the Americas are not included (source: frequencyplansatellites.altervista.org, added ); the All satellites tab shows the first beacons for each satellite.

    Pasting coordinates: copy a spot's coordinates from Google Maps or another map app and paste them into the Latitude box: 24.7136, 46.6753 fills in both latitude and longitude.

    Every calculation runs in your browser. Saved sites and their antennas, footprint files and your satellite list stay in this browser and are never sent to AntennaPointer. The site only counts visits and which features are used, anonymously (see Privacy). Map outlines: Natural Earth (public domain, added ). Gulf city names: GeoNames (CC BY 4.0, added ).

    Data sources & dates

    Open data built into this page, with the date the data refers to and the date it was added. Data changes over time (satellites move, beacons are retuned, streets are built), so treat older data with care.

    DataSourceLicenceData as ofAdded
    Satellite positions ( GEO satellites)CelesTrak active GEO orbital elementsPublic data
    Satellite operating status ( not fully operational)CelesTrak satellite catalogue (SATCAT)Public data
    Other satellite names ( satellites)CelesTrak satellite catalogue annex, SatNOGS DB; plus the names the beacon list usesPublic data / CC BY-SA 4.0
    Beacon & telemetry frequencies ()frequencyplansatellites.altervista.org — Asia, Europe-Africa-Middle East and Atlantic pagesPublic listing
    Frequency plan charts ( satellites, PDF in the frequency-plans folder)frequencyplansatellites.altervista.org (Capitan_Uncino) — “anyone can use and link the data”Free to use
    Magnetic declination (for the magnetic azimuth)World Magnetic Model 2025, NOAA NCEI and the British Geological SurveyPublic domainValid 2025 to 20292026-11-12
    World map outlines and bordersNatural Earth 1:110mPublic domain—
    Gulf coastlines, bordersNatural Earth 1:10mPublic domain—
    Gulf city namesGeoNames cities15000CC BY 4.0
    Offline street map (GCC, MB)OpenStreetMap, via the Protomaps planet buildODbL
    Offline map style, fonts and iconsProtomaps basemaps 5.7.2 (Noto Sans fonts)BSD-3 / SIL OFL 1.1 / CC0—
    Page fontsBarlow and Barlow Semi Condensed by Jeremy Tribby (built into the page)SIL OFL 1.1—
    Offline map viewerMapLibre GL JS 5.24.0, PMTiles 4.5.0BSD-3—
    Online street and satellite mapsEsri World Street Map / World ImageryEsri termsLive (online)—
    Beam footprintsSatBeams (link only, nothing copied)—Live (online)—
    Channels & frequenciesLyngSat (link only, nothing copied)—Live (online)—

    About the data

    The data on AntennaPointer is refreshed regularly from the sources above. The dates show when each piece was taken; satellites move and beacons are retuned over time, so check older data against the live signal.

    Earth station location

    Click to move the Earth station, drag to pan, scroll to zoom

    Are you sure?

    Unlock editing

    Find offsets from a peak

    1. Peak the antenna on a satellite, on a steady signal such as a beacon. For pol, turn the feed for the deepest null on the opposite polarization: the null is much sharper than the peak.
    2. Pick that satellite and type what the antenna controller reads. Leave out any reading you don't have.
    3. For a surer result, add one or two more satellites spread across the arc, each at least 15° above the horizon.